• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to replace door Lock (browne-knapp-2.thoughtlanes.net) Door Locks

Door locks are your primary protection against unauthorised access to your home. The signs of wear and tear, as well as instances like moving into a new house or burglaries, may trigger the necessity of replacing patio door lock your lock.

To begin, you must determine the size of your cylinder by measuring the distance between the adjustment screw and the middle of the knob lock cylinder. This measurement will enable you to buy the right lock.

Deadbolt

Installing a deadbolt is excellent way to protect your door from intruders. The bolt extends into the strike plate on the doorframe when it is locked, making it much more difficult for burglars to break in through the door. A single-cylinder deadbolt can be activated by a key located on the outside and the thumb-turn mechanism located on the interior. A deadbolt is only effective when it's properly installed, though.

You will first need to find out if the door has a hole that is suitable for a deadbolt or if you'll need to drill it out. Mark the location of the hole to install the deadbolt on the surface of the door using the template included with your lock installation kit. Use your tape measure to determine the height of the deadbolt. Then, mark the high point on the outside of the door and use the speed square to draw an even line across the mark you made for the bolt hole.

Then by using a power drill, bore through the hole until it reaches the opposite side of the door. It may take a while. Sand the hole and the edge of the door to smooth it. It's also an excellent idea to stain or paint the door at this point.

Once the door is ready take off any screws that are visible on the deadbolt. This will reveal the front and back assemblies of the deadbolt as well as the bolt inside. Then, remove the bolt and replace it by the new bolt to match the door hardware. The bolt is usually connected to a setplate that you need to unbolt. Once this is done it is time to cut out the space for the strike plate on the door frame.

If your strike plate is not aligned It's likely that the previous installer didn't mortise it correctly or a weatherstripping popped up and changed the strike's position. You will need to re-mortise the strike plate and possibly even the deadbolt to fix this issue. Close and lock the deadbolt when you've completed this step. Make sure the bolt extends into the strike plate and then test the key to make sure it opens and closes smoothly.

Knob

It can make your home or business less secure when the door knob is damaged. It could also make it harder to open or close the door, so it's a good idea to replace it. replacing upvc door lock a knob is a relatively simple DIY project that shouldn't take longer than 30 minutes to complete. You can use a screwdriver or pliers to get rid of the old knob or handle, but be careful not to damage any of the other components on the door.

Spray WD-40 or another dry lubricant, on the mechanism of your door knob prior to you begin. This will assist the new lock move smoothly when you turn it. It's important to use a quality knob and handle that is compatible with your doors currently in order to ensure that the lock is operating properly. If there's no match then you'll have to purchase a new doorknob and latch plate.

To begin the replacement process, look at the knob or handle to see the screws that hold it in place. If there aren't any screws, you can use the screwdriver to insert the cover plate between the hidden screws plate.

Once you've removed the knob that was previously used, look it over for signs of rust or damage. You'll have to scrub it up if there are any marks or dents however you don't need to do anything major when the knob is in good shape.

It's time to install the new knob. You should first examine the two knobs to make sure that you've chosen the right one for the door. You'll need to choose one with an extended rod that's designed to lock into the rod mechanism on the second knob. After you've placed the new knob into the hole then slide it into the latch.

Test the spring by pressing it repeatedly. The latch should then spring back up every time. Then, put in the new knob and connect it to the rod mechanism on the first knob. Attach the other long screws from the knob's interior through the cylinder hole on the doorknob on the outside and secure it.

Latch

A latch is a piece of metal that extends into the door jamb to keep it closed. It is operated by a knob or handle on the interior side of the door or by a thumb turn on the outside side of the door. A latch can be secured using deadbolts to stop intrusions from piercing the glass. It also provides protection from the accidental or deliberate closing of the replacing upvc door lock and handle by pets or children. The latch can be fitted with single cylinder deadbolts or a double cylinder deadbolt, according to the security level you prefer.

Installing a deadbolt is exactly the same as installing a latch, however there are some differences. To make sure that the new lock will fit first, measure the setback on the doorjamb using the tape measure. The setback is measured from the edge of doorjamb all the way to the center of hole for the latch plate. The standard setback is 2 3/8 to 2. 3/4 inches. If your setback is greater than that, you might need to purchase an extra-long latch from a locksmith or hardware store.

The next step is to drill an edge bore hole in the doorjamb for the latch plate. Use a chisel for chiseling out the mortise for the latch, making sure it's deep enough for the faceplate of the new latch to be in a flush position with the doorjamb. Place the strike plate in place to make sure it is positioned correctly.

If the strike is too high, you could knock the door down or apply pressure using a tire iron or crowbar. This can also cause the doorjamb's to crack. To fix this, the strike could be lowered by drilling another hole into the doorjamb and cutting out the core of the hole that was previously drilled.

Installing the new strike plate is the last step. This can be done by screwing the new plate over the existing screw holes. Then you can use wood putty to fill in the screw holes that were previously used and the bolt hole that won't be used. Once the putty has dried you can sand it until it has a smooth finish.

Strike

The piece of metal that connects the latch and deadbolt when the door is closed is an electric strike. It is a crucial component of the overall security of a lock because it keeps the door shut and also provides additional resistance to force or kicks applied to the door. If a door has been equipped with an electric strike, it will only be opened with an entry key or the control unit that controls its electrical impulses.

Traditionally the installation of an electric strike required cutting out a portion of the doorjamb in order to remotely release a cylindrical lock's latchbolt from the pocket within the strike. This is not only ugly and unattractive, but also exposes the latchbolt mechanism and the keeper to intruders.

Recently, several electric strikes manufacturers have created a "No Cut" kind of strike that doesn't require a cutout for operation. They use a specific design that allows the latchbolt and keeper to slide into the pocket without causing damage to the doorjamb's faceplate.

The strike has an internal ramp that lifts the latchbolt and keeper when it receives an electrical impulse from a reader or controller. The keeper and latchbolt are pushed up the ramp by the retraction. When the door is closed the deadbolt is retracted and the latchbolt retracts into the keeper.

Installing an electronic strike is a straightforward procedure, particularly when you're replacing door locks an older strike. If you're planning to upgrade an access control system to an electric strike, you must ensure that your new system is compatible. You will also have to ensure that the strike is connected to your access control system and is set up to function in a safe manner.

Upgrade your strike plates with heavy duty strike plates to stop the entry of unauthorized persons. These plates are fitted with four to six three-inch screws instead of the two, three-fourth inch screws that are typically employed in regular strikes. The longer screws make it difficult for anyone to break the frame and reach inside to turn the thumb turn part of a single cylinder deadbolt.