• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

how to replace a lock on a upvc door to replace door lock (visit the following website) Door Locks

Your first security measure is your door lock. It will prevent unauthorized entry into your home. Locks may require replacement due to signs of wear and tear, or other situations like moving into a new residence or a break-in.

To begin, you must determine the size of your cylinder by measuring the distance between the adjustment screw and the center of the cylinder knob. This measurement will enable you to purchase the appropriate lock.

Deadbolt

If you're looking to ensure that your door is safe from criminals, it's a great idea to install a deadbolt. The bolt extends into the strike plate on the doorframe when it is locked, making it much more difficult for burglars to gain entry into the door. A single-cylinder deadbolt is activated with a key on the exterior, and a thumb-turn piece that is located inside. A deadbolt will only work only if it's correctly installed however.

It is first necessary to determine whether the door already has an existing hole for a deadbolt, or if you'll need to drill it. Utilizing the template included with the lock installation kit mark the location of the deadbolt hole on the door lock replacement's surface. Use your tape measure to determine the height of the deadbolt. Mark this high point on the door's edge. Use speedsquares to draw a straight line across the mark that you made to mark the bolt hole.

Then, using a power drill, bore out the hole until it is on the opposite side of the door. This could take a while. Sand the hole and the door edge to make it smooth. At this stage, it's a great idea also to paint or stain your door.

When the door is in place, remove any screws that are visible on the deadbolt. This will reveal the front door lock replacement cost and back assemblies of the deadbolt and also the bolt inside. Then, unscrew the bolt and replace it with a brand new bolt that matches your door hardware. The bolt is usually connected to a setplate which you'll need to unbolt. After that, you'll have to chisel the door frame for the strike plate.

If your strike plate is out of alignment It could be due to the previous installer didn't mortise it correctly or an installation of a weatherstripping altered the strike's location. To fix this problem it is necessary to remortise both the strike plate and the deadbolt. After this is done check the deadbolt by closing it and locking it. Test the deadbolt by closing and locking it after the bolt has been extended into the strike plate.

Knob

If a door knob is worn out, it can make your home or business less secure. It may make it difficult to open or close the door, which is why it's an ideal idea to replace the knob. It shouldn't take more than 30 minutes. Use pliers or a screwdriver to take off any knobs or handles. Be careful not to harm the other components of the door.

Spray WD-40, or a different dry lubricant, on the mechanism of your door knob prior to you begin. This will allow the new lock move smoothly when you turn it. It's important to use the best knob and handle that is compatible with the doors you currently have to ensure that the lock is operating properly. If you don't have a matching doorknob and handle, you'll need to purchase a replacement.

To begin the replacement process, first look over the knob or handle to find what screws hold it in place. If there aren't any screws, you can use a screwdriver to wedge between the cover plate and the plate with hidden screws and then remove it.

After taking the knob off, inspect it for signs of rust and damage. You'll have to scrub it off if you notice any scratches or marks however, you shouldn't need to do anything If the knob is in good shape.

Install the new knob. You must first study the two knobs to ensure that you are choosing the appropriate one for your door. You'll need to choose one that has an extending rod that's designed to lock into the rod mechanism of the second knob. Once you've put the new knob in the hole and then put it in the latch.

Thread the latch plate screws down and then test the spring by pushing down on it several times. The latch should rise every time. Install the second knob, and lock it to the rod mechanism of the first knob. Thread in the other long screws from the knob's interior through the hole for the cylinder on the doorknob outside and secure it.

Latch

A latch is a steel piece that extends into the doorjamb to keep it shut. It is operated with a knob or handle on the interior side of the door or a thumb turn on the outside side of the door. A latch can be secured with deadbolts to prevent intruders from breaking in through the glass of the door. It can also protect against the accidental or deliberate closing by children or animals. It is possible to install an entry point with either a single-cylinder deadbolt or double-cylinder deadbolt depending on the level you prefer for security.

Installing a latch follows the same steps as installing a deadbolt, however, there are a few variations. To make sure that the new lock will work first, you must determine the setback of the doorjamb with a tape measure. The setback is the distance between the edge of the doorjamb to the middle of the hole to accommodate the faceplate for the latch. A standard setback is 2 3/8 to 2 3/4 inches. If your setback is higher than that, you might need to purchase an extra-long latch from a hardware or locksmith store.

The next step is to drill an edge bore hole through the doorjamb to accommodate the latch plate. Utilize a chisel to chisel the latch mortise. Make sure the depth is enough to allow the faceplate to be flush with the doorjamb. Place the strike plate in place to make sure it's placed correctly.

If the strike is placed too high, the door could be pushed in or pressure applied to it with a crowbar or tire iron. This can also cause the doorjamb's to crack. To remedy this, the strike could be lowered by drilling another hole into the doorjamb and chiseling out the core of the previous hole.

Installing the new strike plate is the final step. This can be accomplished by screwing the new plate over the screw holes that are already in place. Use wood putty afterwards to fill in any existing screw holes or bolt holes that won't be used. Once the putty has dried then sand it to a smooth finish.

Strike

An electric strike is a metal piece where the deadbolt and latch are engaged when the door is shut. It is an essential part of the lock's overall security because it stops the door from opening and gives an additional level of resistance to force or kicking. If a door has been equipped with an electric strike, it can be opened using keys or the control unit that governs its electrical impulses.

In the past, installing an electronic strike required cutting a piece of a doorjamb to let the latchbolt of a cylindrical lock from the pocket within the strike. This is not only unattractive however, it also exposes the mechanism for the latchbolt and the keeper to intruders.

Recently, several electric strike manufacturers have created an innovative type of electric strike, dubbed the "No Cut" strike that doesn't require cutouts in the doorjamb to operate. The strikes have a unique design that allows the latchbolt and keeper to slide into the pocket without causing damage how to replace upvc door lock the faceplate of the doorjamb.

The strike has an internal ramp which lifts the latchbolt and keeper when it receives an indication from the reader. The keeper and latchbolt are pushed up the ramp due to retraction. When the door is closed the deadbolt remains retracted, and the latchbolt retracts into the keeper.

Installing an electronic strike is a straightforward procedure, particularly in the case of replacing an existing strike. If, however, you are upgrading to an electric strike for an access control system, you will be required to ensure that the new system is compatible with the model of lock you've chosen to install. You will also need to make sure that the strike is wired to your access control system and is set up for fail-safe operation.

One method to guard against unauthorized access is to upgrade the strike on your doors to a robust strike plate. The plates are made of up to six screws of three inches instead of the usual two screws of three-fourths inch. The longer screws make it harder for anyone to break the frame and then reach inside to turn the thumb turn part of a single deadbolt cylinder.