• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Go About boarding up windows service up a door (from Nerdgaming)

boarding up houses up a door is one way to protect vacant investment properties from the elements. It's not a guarantee against all damages, but it can help to prevent some of the issues that are associated with severe storms.

Boarding up windows and doors can also deter burglars or vandals from entering your property. Installing plywood boards over openings can be time-consuming and expensive.

Take a measurement of the door

The first thing you'll require is an accurate tape measure. It is a good idea to keep a ladder or chair close to hand in case you need an improved view of the top of the frame. If you need to use these tools, be sure to wear gloves and safety glasses.

Once you have the measuring tool, begin by taking the door width measurement. This can be done by running the tape measure horizontally across the door. Be sure to eliminate any extra door parts such as a door sweep, from this measurement. Then, you can take the height measurement by measuring boarding up services from the floor to the existing sill plate or the lintel. It is crucial to measure in multiple locations, especially when measuring doors older than they may not have the perfect rectangular shape. If the measurements vary take the largest number.

After you've taken the width and height measurements, you'll need to determine the size of board you'll need for the frame. It should be at least 2 inches wider and 1'' higher than the door. 2'' higher. This will give enough space to shim the door and frame into place.

It's a great idea to take off the trim or casing around the jambs of your door to be able to see the studs. This will allow you determine the exact size of the gap between studs and the edges of the frame.

Once you've removed the trim, you can then determine the width of the frame of the door by running the tape over the entire frame in three places and using the smallest measurement as your door's width. Also, you should take a measurement of the height of the frame from top to bottom on both sides, and then use the shortest measurement as the height of your door.

If you're having difficulty with these measurements, it's a good idea to consult a professional and have them visit your home to do the measuring for you. They will tell you what size and type of door you'll need and how to prepare your frame to accommodate a replacement door.

Cut the Plywood

A door frame is typically comprised of studs or thin boards that create a hollow space around the door. Two hinges are attached to the studs and hold the door in its place. This means that if you need to restore the door, it's necessary to remove the door from its hinges overnight. To stop insects from entering your home and to secure the door's opening, a simple method for boarding up windows service the door is to put plywood in the opening. This is easy to do without having to nail or screw the plywood to the frame of the door.

Plywood is a breeze to work with, cheap and looks beautiful once finished. This makes it the ideal material for temporary solutions to a problem that requires removing an existing door while refinishing or installing a new one. It can also be useful for securing the opening in a room that is being renovated, like an unfinished basement or construction site.

To build a wall made of plywood begin by taking measurements of the width and height of the door opening. Note the measurements using an utility blade and a straight edge of metal such as a drywall or a metal square. Then, snap the chalkline along each line to indicate where you want to cut. Finally utilize a circular saw to cut out the plywood to size.

When cutting the plywood it is essential to protect your ears and eyes. If you can wear protective goggles and earplugs while working. It is also important to use a blade with lots of teeth which will permit you to cut quickly and with little tear-out. Utilize a small piece of wood to guide the blade. Hold it a hair's distance from the marked line when cutting.

Attaching a pair or short braces at each end is a good way to secure the plywood in place without putting screws into the studs. Set one brace on the side of the door, and the one on the outside. Position a pair 1-1/2-inch deck screw in each hole and then tighten by using an open-end ratchet.

Secure the Plywood

It's now time to connect the frame to the panel after you have the wood sheet cut to the proper size and the holes for the rails and stiles of the door frame are predrilled. This is a simple project that doesn't require a lot of advanced carpentry skills, as long as you use the right tools and follow the correct steps.

Set up a table in the doorway with two sawhorses on each end, as well as framing 2x4s. Lay the full sheet of plywood flat on top of the sawhorses using the marks left by the measurement process as a reference for cutting. Cut the lines using a utility knife and a drywall square or any other metal straight edge. This will serve as a guide to the saw blade and also prevent splintering of plywood when cutting it.

Wear eye protection and cut along the scored lines using a circular or table saw fitted with a fine-tooth blade. Sand the edges of the panel with 120-grit paper to smooth it out and eliminate any burrs. After sanding process, apply a coat of wood sealer to the plywood panels and let dry as directed by the manufacturer.

Install the hinges onto the door frame. If you're using a T hinge, drill holes in the outside of the door for the strap parts of the hinges. Next, position the outside hinge on its mark and attach it onto the frame using a screw gun. Repeat the procedure for every hinge on the inside of your door. Be careful not to overtighten them, or the panel could shift.

If you are using a single outside T-hinged door, you can make it easier to lock and close using a chain latch by fishing a piece of wire through the loops on the hinges on the outside. Bend a small piece of tie wire in half and put it through the two holes on the exterior of the door. You can then connect the wires to tighten them and lock the door.

Install the Plywood

With the measurements you made using the measurements you took, put the plywood in the door opening. Adjust the header (top) of the frame and the sill (bottom). Use a level to make sure there's no slop in either the header or sill. If the level isn't perfect then put a second shim in the area you need it and repeat the procedure until you've got the sill and the header to be level.

Once the plywood is set, secure it with the stainless-steel hinge bolts and wingnuts. It is a good idea to utilize a screw gun that has an attachment for a hex-head to keep the head from being stripped of the screws.

If your home has studs that run along the length of your doorway, you can drill hanger bolts into each framing member. This is much simpler than using a drywall saw to create the hole.

After installing the plywood, measure the width and height of the door opening. If necessary, trim the bottom of the plywood to match the height of your door frame and cut two pieces of framing lumber as braces that are positioned across the upper and lower edges of your door. Cut along the lines marked on the plywood with circular blades with teeth that are finely-toothed. Wear eye protection. Splinters can be removed from the cuts using a sanding tool.

After you have the two braces in place Attach each brace to the plywood with pairs of 2-inch finishing nails. When you're finished, counter sink the heads of all the nails. Seal the braces and the plywood with a good wood sealer such as this wipe on polyurethane from Minwax.

If your door is too large, you can either add decorative molding to fill in the space between your door and jamb or you can reduce the size of your opening. However, in most situations, it's more affordable and simpler to just find an alternative door. It also eliminates any issues you might have encountered with your door's original model even if it was damaged or not suitable for the opening.