• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Ghost 2 Immobiliser Reviews

The Ghost 2 immobiliser uses the latest technology to ward off car theft. This hidden device is not detected by thieves and will only start your engine when an app or PIN code is entered.

It is weatherproof and connects to the CAN data network of your vehicle. It also comes with a service/valet mode, which allows you to temporarily start your car when it's in the garage for servicing or cleaning.

Easy to install

The Ghost immobiliser is a cutting-edge security gadget that safeguards your vehicle from hacking, cloning and key theft. It utilizes a unique PIN code system that is incorporated into the car's ECU which makes it extremely difficult for thieves to detect or tamper with. In contrast to traditional immobilisers, it does not require any special keys or sensors and is completely hidden without any LED indicators or signals to signal its presence. It's also cheaper than replacing an ECU, or installing a key fob. It can even lower your insurance premiums.

Follow the directions of the manufacturer when installing follow the manufacturer's instructions when installing a Ghost 2 vehicle immobiliser. This will ensure that the device operates correctly and effectively. After the installation is completed, test the system by entering the PIN code and starting the engine. Regular testing will enable you to identify any problems early on.

Check the location of the the CAN H and L wires prior to beginning the installation. They are crucial for powering the immobiliser, therefore it is essential that they are connected properly. Labeling the wires will make it easier to find them during installation. Once you have located the wires, connect them both to a power supply of 12V and an earthing source. Use the fuse tap to safeguard the connections from short-circuits or damage.

After connecting the wires, tidy the wiring using cable ties to avoid potential interference. You can also cover the connections with insulation tape or heat-shrink tubing. This will protect them from electrical shorts and increase the life span of the device. Once the wiring is secured it's a good idea test the Ghost 2 immobiliser.

In situations where you have to surrender your vehicle, for instance for valet parking or servicing, the Ghost 2 immobiliser has a service mode that temporarily disables the PIN code sequence. Press the brake pedal and hold down the accelerator for a number of presses equal to the first digit in the emergency code. The system will then enter service mode, which can be confirmed by flashing the indication signal 5 times.

Change PIN codes quickly

It is easy to protect your vehicle from theft by installing the ghost 2 immobiliser. It is installed discreetly within the vehicle, and is accessible only through a specific code. The device communicates directly with the vehicle ECU via its data bus. It does not rely on radio frequency signals as do traditional Thatcham immobilisers or other aftermarket alarm systems. This makes it harder for thieves to detect the sound of an immobiliser relay or add new keys. The control unit is hidden in the wiring of the vehicle or dashboard, and cannot be physically altered to reset the system.

The ghost 2 immobiliser is connected to your vehicles CAN Data network and utilizes the buttons already present on the steering wheel, door panels and the central console to generate an individual sequence of up to 20 button presses which must be entered before the engine can begin as it would with the PIN code. This unique system is reprogrammable and does not require cutting wires when installing. You can also put your vehicle in Valet or Service mode to allow it to be started for a short time when you give it to a mechanic to work.

You can also make use of the app to alter your PIN code or disable it completely if lost your keys. This feature is particularly helpful in the event that you've lent your car away to another person for parking or valet service. It stops them from starting the car and then driving it off without your consent. It's also unnoticeable by professional thieves, as it doesn't utilize radio frequencies or circuit cuts.

Another excellent feature of the ghost 2 immobiliser is its capability to prevent thefts of relays. Relay theft is one of the most frequent methods of car theft. The criminals hack your car's diagnostic ports then modify the signal sent by the car's ECU to fool it into thinking that the car's key is valid and present. The immobiliser of the traditional model is able to be bypassed this manner, however with the ghost 2 immobiliser the signal is blocked by the immobiliser prior to it reaches the ECU.

Easy to use app

Ghost 2 is a revolutionary immobiliser that shields your vehicle from hacking, key-cloning and key theft. It connects to the CAN data network of your vehicle and demanding that you enter a pin code before it will start the engine. It also stops thieves from using signal spoofing or device spoofing, which are common tactics employed to steal vehicles.

The system is easy to use and functions as a normal car alarm. Installing the system allows you to create a unique 20-digit pin code that you must enter before you start the vehicle. This will stop the vehicle from being stolen even if the keys are taken away. If you wish to disable the system you can do this via an app on your smartphone.

Contrary to other systems it is completely silent and doesn't emit any radio frequency signals. It is a weatherproof, discrete device that can be positioned anywhere inside your vehicle. It can be hidden under the dash, steering wheel, or on the door panels. It communicates with your ECU via the CAN data circuit, and is not affected by diagnostic tools that thieves use to identify security systems. It is not affected by jamming devices which spoof codes.

It is a hidden installation that does not require any wire cutting or modifications to the vehicle, and it can be employed as an anti-theft device for all cars. Its technology has been proven to be efficient, and it's in compliance with TASSA Standards. The ghost is a fantastic solution for classic, sports and prestige cars, and it can be used to safeguard vehicles that are let out on websites like Turo.

The Autowatch Ghost 2 represents the next generation of auto immobilisers. This system is undetectable to thieves and blocks the vehicle from starting until they have your PIN or are authorised by the app. It also does not emit any radio frequencies or other signals that could be detected by scanners. Installation is fast and simple. The app is simple to navigate and offers a user-friendly interface which makes it easy to configure and use. It also includes a GPS tracker to assist police locate and locate the vehicle.

Simple to reset

It is possible to secure your vehicle from theft by using an immobiliser ghost 2. It connects to your vehicle's ECU to create a barrier that thieves are unable to penetrate without the correct PIN. The device is also TASSA-certified which means it is acknowledged by insurance companies. It's a great tool to prevent car stolen with ghost immobiliser theft and can save you money in the long run.

In contrast to traditional alarms and immobilisers that require cutting circuits and circuit cutting, the ghost immobiliser 2 system is directly connected to the vehicles CAN data network and operates using the buttons you already have on the dashboard and the steering wheel. You can create a unique PIN that is up 20 presses in length. The PIN must be entered before the engine can be started, just as with the credit card's PIN. The ghost immobiliser for sale system is invisible to thieves and has no LEDs to signal its presence. This makes it the most effective aftermarket CAN-bus immobiliser on the market today.

The Ghost system has another benefit: it does not transmit radio frequency signals. This means it is not detected by thieves or snatched up. This is a deterrent to cloned key attacks and relay attacks as and the typical method of hacking into a car's computer system using its CAN bus by searching for signals. The ghost car immobiliser system is designed so that it is able to be hidden within your vehicle. There are no LEDs or other signals to indicate its presence.

The system comes with a Transport Mode which disables the Ghost System. This is helpful in situations where you need to temporarily deactivate Ghost for instance, when transporting or servicing your vehicle. This mode isn't as effective as Service Mode as it doesn't disable the Ghost system when you exceed 31 mph in 15 minutes.

To reset your ghost 2 immobiliser, you will need to have the emergency code, which is available from your installer. It is typically hidden under an area for scratch-offs on the card that was provided with the installation. This emergency code should be secured and stored in a secure place, such as a wallet at home.