• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace a Kia Sportage replacement car keys kia Key

The key of a lot of Kia models has an entry system that is keyless in. The key functions like a remote control, and can be exchanged with a kia fob replacement dealer.

Key fobs might stop working due to a variety of reasons, including batteries that are dead, worn buttons signals, signal interference, water damage, and a defective receiver module. Here are some helpful tips to assist you in getting your Kia key fob that is a replacement for the sportage again.

How to replace the remote key or smartkey

Whether your 2011 kia sportage key Fob comes with an intelligent key, remote key push-to-start keys, or a regular non-transponder steel key the battery in these keys will eventually need replacing. This is particularly in the event that your car displays a message that the remote or smart key has low battery power.

It's quite simple to do. To replace the battery in the keyfob remove your mechanical key from the slit that is located at the back of the fob. Then, pry the cover open. A small screw will be located inside the key fob to keep the battery in the correct position. By using a small screwdriver loosen the screw and remove the battery that was in place. Install the new battery and then close the cut on the key fob.

Test the key fob by pressing the lock or unlock buttons. If the doors unlock and lock according to your expectations, then you're good to go! You can now use the hands-free feature to lock and unlock your Kia when your fingers get cold or you need to complete errands in Brandon.

Not all keys may require to be programmed (transponder chips or smart keys). This requires a particular programming machine that only the dealer or locksmith can access. Other keys (non-transponder metal keys) don't require programming. If your key requires to be programmed, you must be aware of the key code number printed on the tag that identifies the key and then record it in a safe location.

How to replace a battery

If your Kia key fob isn't responding when you press the lock or unlock button on the fob, it is a signal that the battery should be replaced. A weak battery can cause other problems like the check engine light turning on or the engine not cranking. It is quite simple to replace key fob battery with just two tools.

Before beginning the process ensure that your vehicle is off and all doors are closed. Find the small, metal or plastic piece near the bottom of the key fob. Then, jiggle it until the metal key comes out. Then, you can insert the key into the handle on the door of your driver to unlock your car.

To replace the battery inside the key fob, you must remove the rear cover. Use a pry tool to open the latch that holds the black negative cable. Remove the old battery, and then align the replacement battery in a way that its "+" side faces you, and the "-", negative side is facing the fob's electrical contacts. Push the new CR2032 battery straight into position with care to avoid using too much force to avoid bending or damaging the contacts of the metal.

After installing the new battery after which you turn the key fob on and off in the ignition until the door locks up. Then you can test your Kia key fob to see whether it's working again.

How do you replace a smart key

Depending on the model of the Kia Sportage, you may have the standard key fob, or a smart key kia key. The difference between them is that the smart key has a small mechanical key blade that is hidden inside, while the standard fob doesn't. Both key fobs are equipped with a battery that will eventually require changing. Fortunately, it's an easy process that takes only two minutes.

Make sure you turn off your 2013 kia optima key and sit on a flat, well-lit surface before you begin. Be aware that the fob can contain small pieces that could be thrown off should you not be careful.

The small release button is located on the lower backside. This will either be an oval silver button or a rectangular slot. You can open the key fob by pressing the button.

Once the key fob is opened, take out the battery. The new battery is a CR-2032, and can be purchased from a local or online auto parts store. After you've finished, your key fob should be able to lock or unlock and start your vehicle even if it's not running.

How do you replace the mechanical key?

The Kia keyfob is a wonderful convenience that lets us lock or unlock our car simply by pressing one button. But, as with all devices there are issues with it occasionally. There are solutions to resolve these issues and keep your key fobs running for many years.

A dead or low-quality battery is among the most frequently encountered issues. This can cause the device to stop working altogether or even to stop working intermittently. If this is the case try replacing the battery with a fresh new one.

If this doesn't fix the problem you can try using a standard flathead screwdriver to open the fob's plastic casing. Be careful not to damage internal components, or scratch the plastic. After the battery has been removed and replaced with a new one.

Close and open the door using the mechanical key. (Every kia venga key fob comes with an emergency mechanical key which will fit into the slot). Test the key fob and make sure it is working correctly. If the device not working, contact a locksmith or dealer to resolve the problem. To avoid lockouts in the future, ensure you purchase an emergency key that will work on all door and trunk cylinders.